These Single Thread U-Nuts accommodate an unusually wide range of panel thicknesses from 0.025" to 0.150" which satisfies most needs for sheet metal and plastics assembly. A single wide-range U-Nut can replace as many as 5 or 6 separate size nuts required to cover the same capacity and it can be supplied in 8 AB through 16 AB thread sizes.

U-Nuts, also called U-Shaped Speed Nuts®, are self-retained in the screw-receiving position to provide simple and rapid attachment of mating panels. They will not turn when the screw is driven and will not corrode or freeze on screw threads. Typically, U-nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance, single thread nuts are placed over the edge of a stamped panel, or through a pre-stamped slot, then pushed until the fastener inner back locates against the plastic or metal panel edge or snaps into the clearance hole. In addition, the U-Nut's impression actually cleans out rust, dirt or paint clots from the screw threads as they are removed.

U-Nuts, also called U-Shaped Speed Nuts®, are self-retained in the screw-receiving position to provide simple and rapid attachment of mating panels. They will not turn when the screw is driven and will not corrode or freeze on screw threads. Typically, U-nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance, single thread nuts are placed over the edge of a stamped panel, or through a pre-stamped slot, then pushed until the fastener inner back locates against the plastic or metal panel edge or snaps into the clearance hole. In addition, the U-Nut's impression actually cleans out rust, dirt or paint clots from the screw threads as they are removed.

U-Nuts, also called U-Shaped Speed Nuts®, are self-retained in the screw-receiving position to provide simple and rapid attachment of mating panels. They will not turn when the screw is driven and will not corrode or freeze on screw threads. Typically, U-nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance, single thread nuts are placed over the edge of a stamped panel, or through a pre-stamped slot, then pushed until the fastener inner back locates against the plastic or metal panel edge or snaps into the clearance hole. In addition, the U-Nut's impression actually cleans out rust, dirt or paint clots from the screw threads as they are removed.

U-Nuts, also called U-Shaped Speed Nuts®, are self-retained in the screw-receiving position to provide simple and rapid attachment of mating panels. They will not turn when the screw is driven and will not corrode or freeze on screw threads. Typically, U-nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance, single thread nuts are placed over the edge of a stamped panel, or through a pre-stamped slot, then pushed until the fastener inner back locates against the plastic or metal panel edge or snaps into the clearance hole. In addition, the U-Nut's impression actually cleans out rust, dirt or paint clots from the screw threads as they are removed.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance "U" nuts are placed over the edge of a stamped panel, or through a pre-stamped slot, and are simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. They are self-retained in the screw-receiving position to provide simple, rapid attachment of mating panels and cannot turn as the screw is driven.

These U-Nuts will not freeze on screw threads. In fact, the U-Nut's impression actually cleans out rust, dirt or paint clots from the screw threads as they are removed.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels. They cannot turn as the screw is driven.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels. They cannot turn as the screw is driven.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels. They cannot turn as the screw is driven.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels. They cannot turn as the screw is driven.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels and cannot turn as the screw is driven.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels. They cannot turn as the screw is driven.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels. They cannot turn as the screw is driven.

Single Thread U-Nuts are used where a full bearing surface on the lower leg is desired. During assembly, these high-performance U-shaped nuts are placed over the edge of a stamped panel, or through a pre-stamped slot. They are then simply pushed until the rear of the fastener locates against the plastic or metal panel edge or snaps into the clearance hole. U-Nuts are self-retained in screw-receiving position to provide simple, rapid attachment of mating panels. They cannot turn as the screw is driven.

J-Type U-Nuts press easily into a self-retained position over panel edges or in center panel locations. They are ideally suited for blind assembly or hard-to-reach installation. They offer floating alignment to speed production and lessen rejection. No special tools, skills or equipment are required. Riveting, welding, clinching, staking and other secondary fastening devices are eliminated.